Industry news

Relativity Rewrites Chemical Bonds in Heavy Elements. It Also Makes Most of Your Car Battery’s Voltage

A frost-covered black 12-volt lead-acid car battery under an open hood at winter dawn, with a red and a black cable on its terminals and a frosted lawn and house behind
ChemNN Chemistry news, explained. Watch live on YouTube (opens in a new tab)

Turn the key on a cold morning and the engine turns over on a chemical reaction between lead, lead dioxide and sulfuric acid. What makes that reaction strong enough to crank an engine is not in the chemistry textbook chapter on batteries. It is in physics. Roughly four-fifths of the voltage in every cell of a lead-acid battery comes from the effects of special relativity on the electrons of a heavy atom. This month, a Brown University study on exactly those effects went back into circulation, and it is a good moment to explain the battery under the hood.

This article sets out what the Brown team found, what a 2011 calculation showed about the lead-acid battery, why there is no tin battery, and where the sulfuric acid electrolyte fits. The physics figures are quoted from the published papers; where we multiply them out, the result is labelled as our arithmetic.

2.11 VMeasured standard voltage of one lead-acid cell (Ahuja et al., 2011)
1.7–1.8 VShare of that voltage that comes from relativistic effects
0.39 VCalculated cell voltage with relativity switched off
~2.3 VA six-cell 12-volt battery without relativity (our arithmetic)

What did the Brown University study find?

That in heavy elements, the textbook picture of a triple bond breaks down. The team, led by Brown Ph.D. students Deniz Kahraman and Jie Hui with chemistry professor Lai-Sheng Wang as corresponding author, studied a small charged molecule of carbon and bismuth, CBi−, with photoelectron spectroscopy: laser light knocks electrons out of the molecule, and their energies map out the bonds. The paper, “Relativistic collapse of the classical triple bond in the CBi− molecular ion”, appeared in Science on 9 July 2026 and was widely republished in early November.

School chemistry teaches that a triple bond is one sigma bond plus two pi bonds. In CBi− that split stops being clean. “This idea that relativity is important in heavy elements has been around since the 1970s,” Wang said in the university’s release. “But we show direct spectroscopic evidence that what we learned in high school about chemical bonding isn’t true in heavy elements.”

Bismuth has atomic number 83. Lead, at 82, sits immediately to its left on the periodic table, and the same physics that blurs the bonds in bismuth is what gives a lead-acid battery its punch.

What does relativity have to do with a car battery?

Almost everything that makes it useful. In 2010 a team of five physicists and chemists from Sweden and Finland, Rajeev Ahuja, Andreas Blomqvist, Peter Larsson, Pekka Pyykkö and Patryk Zaleski-Ejgierd, calculated the energy of the battery reaction from first principles three ways: with no relativity, with the main (scalar) relativistic effects, and with full relativity. The paper, “Relativity and the lead-acid battery”, was published in Physical Review Letters in 2011. Its abstract states the result in one line: “All calculations agree in that 1.7-1.8 V of this standard voltage arise from relativistic effects, mainly from PbO2 but also from PbSO4.”

Level of physics in the calculation Cell voltage (average of methods)
Non-relativistic (Newtonian electrons) +0.39 V
Scalar-relativistic +2.30 V
Fully relativistic, including spin-orbit coupling +2.13 V
Measured in the laboratory +2.107 V

The fully relativistic answer lands within about 0.02 volts of the measured one. The non-relativistic answer misses by more than a factor of five. The authors also split the relativistic gain by ingredient: at one level of theory, lead dioxide contributes +1.58 V, lead sulfate +0.27 V and metallic lead −0.06 V. The positive plate does nearly all of the work.

Bar chart of the calculated standard voltage of one lead-acid cell: 0.39 volts with no relativity, 2.30 volts scalar-relativistic and 2.13 volts fully relativistic, against a measured 2.107 volts; a bracket marks the 1.7 to 1.8 volts that come from relativity
Calculated cell voltage at three levels of physics, average of methods, against the measured 2.107 V. Data: Ahuja et al., Physical Review Letters 106, 018301 (2011).
Without relativity, the 12-volt battery in your car would make about 2.3 volts.

That line is our arithmetic: a car battery is six cells in series, and six times the non-relativistic 0.39 V is about 2.3 V. With relativity, six times the measured 2.107 V is 12.64 V, which matches the 12.65-volt open-circuit reading that the Battery Council International table gives for a fully charged starter battery.

Why does relativity matter for lead and not for lighter metals?

Because lead’s nucleus is heavy enough to pull its electrons up to a large fraction of the speed of light. A common rule of thumb puts the speed of an atom’s innermost electron at about Z/137 of light speed, where Z is the atomic number. For lead, Z is 82, so about 60% (our arithmetic). At those speeds the electron behaves as if heavier, and the s orbitals, which reach in close to the nucleus, contract and drop in energy. For lead the one that matters is the outer 6s orbital.

The paper puts it plainly: “The Pb 6s states are significantly stabilized by inclusion of relativity also in β-PbO2.” Lead’s two 6s electrons are held so tightly that lead prefers the +2 state, the one where it keeps them. In lead dioxide, lead is forced into the +4 state, with those two electrons removed. Given any chance, it takes them back. That hunger is what makes lead dioxide a strong oxidiser, and a strong oxidiser at the positive plate is what produces a high cell voltage.

How strongly the effect scales. Relativistic effects grow roughly with the square of the nuclear charge. The paper compares tin (Z = 50) with lead (Z = 82): (50/82)2 = 0.372. Tin, one row up in the same group, gets little more than a third of lead’s relativistic push.

Why is there no tin battery?

Tin sits directly above lead in group 14, forms the same kinds of oxides and sulfates, and is cheaper and less toxic, yet nobody builds a tin-acid battery. The paper records that “no corresponding ‘tin battery’ exists”, and gives the reason earlier chemists had offered: “the lower oxidative power of tin dioxide, as compared to lead dioxide.” Its own calculation supports that: “a tin battery would roughly correspond to a lead battery without relativistic effects”.

Model reaction M + MO2 → 2 MO Measured EMF What it means
M = lead (Pb) +0.82 V Lead dioxide readily pulls electrons from lead metal
M = tin (Sn) −0.085 V Tin dioxide does not; the reaction will not run as a battery

The same oxide chemistry, one row apart, gives a working reaction for lead and a slightly negative one for tin. In the paper’s calculations the non-relativistic values for the two elements come out similar; only once relativity is switched on does lead pull ahead. In plain terms, a lead-acid battery is the battery tin would be if tin were heavy enough.

Comparison of lead and tin atoms: lead has 82 protons and tin 50, so tin gets 0.372 of the relativistic effect; lead dioxide gives a model-reaction EMF of plus 0.82 volts and tin dioxide minus 0.085 volts, and only lead has a working battery
Lead and tin compared: atomic number, relativistic scaling (ZSn/ZPb)² and the measured EMF of the model reaction M + MO2 → 2 MO. Data: Ahuja et al. (2011).

Where does the sulfuric acid come in?

It is both the electrolyte and a reactant. On discharge, the lead plate and the lead dioxide plate both turn into lead sulfate, and the sulfate comes out of the acid: Pb + PbO2 + 2 H2SO4 → 2 PbSO4 + 2 H2O. Charging runs it backwards and returns the sulfate to the liquid. Battery University describes it from the hydrometer’s point of view: “When the lead acid battery accepts charge, the sulfuric acid gets heavier, causing the specific gravity (SG) to increase.”

That is why the density of the electrolyte doubles as a fuel gauge. The industry table for a starter battery, read at about 26°C after a 24-hour rest:

State of charge Specific gravity 12-volt open-circuit voltage
100% 1.265 12.65 V
75% 1.225 12.45 V
50% 1.190 12.24 V
25% 1.155 12.06 V
0% 1.120 11.89 V

Source: Battery Council International figures as published by Battery University. Manufacturers vary the full-charge number: “While BCI (Battery Council International) specifies the specific gravity of a fully charged starter battery at 1.265, battery manufacturers may go for 1.280 and higher.” Trojan Battery, for its deep-cycle flooded batteries, gives a factory specification of 1.277 +/- 0.007.

Why winter is hard on a weak battery. As a battery discharges, the acid moves into the plates and the electrolyte becomes more like plain water, which freezes far more readily than charged electrolyte. Cold also slows the reaction itself. A battery left half charged through a cold snap is the one that fails. Our winter battery care guide covers freezing, watering and storage for flooded lead-acid batteries.

How do you read a battery’s acid with a hydrometer?

By sampling each cell and correcting the reading for temperature. A hydrometer is a glass tube with a float; the denser the electrolyte, the higher the float rides. It works only on flooded batteries with removable vent caps. Trojan’s procedure starts with a warning that runs against instinct: “Do not add water at this time.” Fresh water sits on top of the acid until charging mixes it, and a reading taken after topping up looks weaker than the battery really is.

  1. Fill and drain the hydrometer two to four times in the cell before taking a sample, so the float and glass are at electrolyte temperature.
  2. Draw enough electrolyte to float the bulb freely, read it at eye level, record it and return the sample to the same cell.
  3. Repeat for every cell, then replace the vent caps and wipe off any spilled electrolyte.
  4. Correct each reading to 80°F (26.6°C). Trojan’s rule: “Add 0.004 to readings for every 10º F (5.6º C) above 80º F (26.6º C)”, and subtract the same below.

The correction matters most in winter. Take a cell that reads 1.245 on a 40°F morning. That is 40 degrees below 80°F, four steps of 0.004, so the corrected reading is 1.229: about three-quarters charged on the BCI table, not the close to 90% the raw number suggests. The correction is our arithmetic on Trojan’s rule. If a battery still reads low after a full charge, Trojan lists the usual causes as age, a battery left discharged too long, or a bad cell.

What this means on a specification

Relativity sets the voltage; maintenance keeps it. In a flooded battery, charging splits off water as gas, so the level drops while the acid stays behind. The rule from Trojan’s maintenance guide is short: “Use distilled or deionized water only.” and “Never add acid to a battery.” Electrolyte is for filling new or rebuilt cells, not for topping up working ones. The table matches the job to the product.

Job Product What to check
Topping up flooded cells after charging Battery Water ACS Reagent Grade Deionized, low conductivity; add after a full charge, to the level the battery maker specifies
Filling new or rebuilt flooded cells with ready-mixed electrolyte Sulfuric Acid 37% - Battery Acid Technical Grade Specific gravity against the battery maker’s figure; our listing gives 1.28 at 20°C
Mixing electrolyte to a set specific gravity in a shop Sulfuric Acid 50% Electrolyte Grade Assay and specific gravity on the certificate of analysis; always add acid to water

Sulfuric acid at any of these strengths is corrosive to skin and eyes, and charging batteries give off hydrogen. Read the safety data sheet, wear eye protection and acid-resistant gloves, work with ventilation and keep sparks and flames away from the vent caps. For the differences between the two liquids that go into a battery, see our battery acid vs battery water guide; for the electrolyte itself, our guide to 37% battery acid.

About supply. This article reports two published physics and chemistry studies and standard battery-maintenance figures. It makes no claim about ours: it does not say where the sulfuric acid or water we list is made, by whom, or how any battery market affects their supply or price.

Common questions

How much of a car battery’s voltage comes from relativity?

About 1.7 to 1.8 volts of the 2.11-volt standard voltage of each lead-acid cell, according to the 2011 Physical Review Letters calculation by Ahuja, Blomqvist, Larsson, Pyykkö and Zaleski-Ejgierd. That is roughly four-fifths. Most of it comes from the lead dioxide in the positive plate.

What would a car battery make without relativity?

The non-relativistic calculation gives about 0.39 volts per cell. A car battery has six cells in series, so it would make about 2.3 volts instead of about 12.6 (our arithmetic), far short of what a starter motor needs.

Why does relativity affect lead?

Lead has 82 protons, so its innermost electrons move at a large fraction of the speed of light. Relativistic effects contract and stabilise its 6s orbital, which makes lead hold its last two outer electrons tightly. Lead dioxide, where lead has lost them, is therefore a strong oxidiser, and that drives the cell voltage.

Why is there no tin battery?

Tin is lead’s lighter neighbour in group 14, but its dioxide is a much weaker oxidiser. The 2011 study found that a tin battery would roughly correspond to a lead battery without relativistic effects. The measured EMF of the tin model reaction is slightly negative, −0.085 V, against +0.82 V for lead.

What did the Brown University relativity study show?

Published in Science on 9 July 2026, it gave direct spectroscopic evidence from the carbon–bismuth ion CBi− that relativity blurs the textbook split of a triple bond into one sigma and two pi bonds in heavy elements. Bismuth sits next to lead on the periodic table.

Should I add battery acid or water to a car battery?

Water. Charging a flooded battery loses water, not acid, so top it up with distilled or deionized water after a full charge. Trojan Battery’s guidance is to never add acid to a battery. Electrolyte is used to fill new or rebuilt cells.

References & Authoritative Sources

Physics figures are quoted from the 2011 paper and its arXiv preprint; the Brown study from the university’s release. Battery figures are from Battery University (BCI table) and Trojan Battery. Multiplications are our arithmetic and are labelled in the text.

  1. Relativity and the lead-acid battery — R. Ahuja, A. Blomqvist, P. Larsson, P. Pyykkö, P. Zaleski-Ejgierd, Physical Review Letters 106, 018301 (2011). Preprint: arXiv:1008.4872.
  2. Einstein’s relativity rules chemical bonds in heavy elements, new research shows — Brown University via EurekAlert, 9 July 2026.
  3. Relativistic collapse of the classical triple bond in the CBi− molecular ion — D. Kahraman, J. Hui et al., Science (2026).
  4. BU-903: How to Measure State-of-charge — Battery University. BCI specific-gravity and voltage table for starter batteries.
  5. Battery Maintenance — Trojan Battery Company. Watering and specific-gravity testing of flooded batteries.

What we stock

Alliance Chemical Sulfuric Acid 37% Battery Acid Technical Grade container with product label

Sulfuric Acid 37% - Battery Acid Technical Grade

Ready-mixed electrolyte for filling new or rebuilt flooded cells. Quart to tote.

Alliance Chemical Sulfuric Acid 50% Electrolyte Grade container with product label

Sulfuric Acid 50% Electrolyte Grade

For shops mixing electrolyte to a set specific gravity. Quart to tote.

Alliance Chemical Battery Water ACS Reagent Grade container with product label

Battery Water ACS Reagent Grade

Deionized water for topping up flooded cells. Quart to tote.

Maintaining a fleet of flooded batteries?

Tell us the battery type, the number of cells and the volumes you use. We will send the safety data sheet and, on request, the certificate of analysis for the lot you would receive, so you can check specific gravity and assay against the battery maker’s figures.

Read the 37% battery acid guide

Key numbers and sources

Figure Value Source
Standard voltage of one lead-acid cell 2.107 V measured; 2.13 V calculated Ahuja et al., PRL 2011
Voltage from relativistic effects 1.7–1.8 V per cell Ahuja et al., PRL 2011
Non-relativistic cell voltage 0.39 V Ahuja et al., PRL 2011
Six-cell battery without relativity About 2.3 V Our arithmetic
Tin vs lead model reaction EMF −0.085 V vs +0.82 V Ahuja et al., PRL 2011
Full-charge specific gravity, starter battery 1.265 (BCI); 1.280 and higher by some makers Battery University
Hydrometer temperature correction 0.004 per 10°F away from 80°F Trojan Battery
Relativistic bonding in CBi− (carbon–bismuth) Published 9 July 2026 Science; Brown University release

Frequently asked questions

How much of a car battery's voltage comes from relativity?

About 1.7 to 1.8 volts of the 2.11-volt standard voltage of each lead-acid cell, according to the 2011 Physical Review Letters calculation by Ahuja, Blomqvist, Larsson, Pyykkö and Zaleski-Ejgierd. That is roughly four-fifths. Most of it comes from the lead dioxide in the positive plate.

What would a car battery make without relativity?

The non-relativistic calculation gives about 0.39 volts per cell. A car battery has six cells in series, so it would make about 2.3 volts instead of about 12.6 (our arithmetic), far short of what a starter motor needs.

Why does relativity affect lead?

Lead has 82 protons, so its innermost electrons move at a large fraction of the speed of light. Relativistic effects contract and stabilise its 6s orbital, which makes lead hold its last two outer electrons tightly. Lead dioxide, where lead has lost them, is therefore a strong oxidiser, and that drives the cell voltage.

Why is there no tin battery?

Tin is lead's lighter neighbour in group 14, but its dioxide is a much weaker oxidiser. The 2011 study found that a tin battery would roughly correspond to a lead battery without relativistic effects. The measured EMF of the tin model reaction is slightly negative, -0.085 V, against +0.82 V for lead.

What did the Brown University relativity study show?

Published in Science on 9 July 2026, it gave direct spectroscopic evidence from the carbon–bismuth ion CBi- that relativity blurs the textbook split of a triple bond into one sigma and two pi bonds in heavy elements. Bismuth sits next to lead on the periodic table.

Should I add battery acid or water to a car battery?

Water. Charging a flooded battery loses water, not acid, so top it up with distilled or deionized water after a full charge. Trojan Battery's guidance is to never add acid to a battery. Electrolyte is used to fill new or rebuilt cells.

Related Chemical Collections

Share

LinkedIn X Email

About the author

Andre Taki

Chief Commercial Officer, Alliance Chemical

Andre Taki is the Chief Commercial Officer at Alliance Chemical, where he oversees product sourcing, technical support, and customer solutions across a full catalog of industrial, laboratory, and specialty chemicals. With hands-on expertise in chemical applications, safety protocols, and regulatory compliance, Andre helps businesses in manufacturing, research, agriculture, and water treatment find the right products for their specific needs.

This article is for informational purposes only.

Alliance Chemical · Taylor, Texas · since 1998

Pint to tote, priced online. Ships in 1–2 business days.

Order any size online with no minimum. For multi-drum, tote or recurring supply, ask for a quote with freight and net-30 terms.

Shop Sulfuric AcidRequest a bulk quote

55,000+ customersUPS Ground for parcelsLTL freight for drums & totes

Contents